How to Make Fabric Covers for Shoulder Pads

To make fabric covers for shoulder pads, wrap each pad in lightweight fabric cut on the bias, shape the fabric around its curve, and stitch the edges closed. A turned-in edge gives the neatest finish inside an unlined garment; a serged edge is quicker when exposed stitching is acceptable. The method below uses the shoulder pad itself as the template, so you do not need a purchased pattern.

Choose Fabric That Follows the Shoulder Pad’s Shape

A cover protects exposed foam or batting and makes the inside of a garment look finished. It should follow the pad’s shape without flattening it, adding noticeable bulk, or pulling the garment out of line.

Start with pads that already give the garment the right silhouette. Covering a pad will not correct excessive thickness, an unsuitable shape, or foam that is crumbling.

For the cover, choose a lightweight, supple fabric:

  • Garment lining fabric makes a smooth cover that slips easily against clothing.
  • Fine cotton batiste or lawn is manageable for hand sewing and comfortable against the body.
  • Lightweight garment fabric can coordinate with an unlined blouse or jacket, provided it is not stiff or bulky.

Avoid firm materials that resist curving. For a sheer garment, check the proposed cover fabric beneath the outer fabric before cutting; even a neatly covered pad can show through.

What You’ll Need

  • Shoulder pads
  • Lightweight cover fabric
  • Matching sewing thread and a hand-sewing needle
  • Fabric scissors
  • Pins or sewing clips
  • Fabric marker or chalk
  • Ruler or sewing gauge
  • Optional sewing machine or serger

If the finished garment will be washable, prepare washable cover fabric before cutting so later shrinkage does not tighten it around the pad.

How to Sew Fabric Covers for Shoulder Pads

Use bias-cut fabric for shaping, and choose exposed overlocking only when its appearance is acceptable.

Choose your finish before cutting; it determines whether the raw edges need room to turn inward.

Finish Best Choice When Finished Appearance
Turned-in edge, hand sewn You want close control around a curved or soft pad Enclosed raw edges with discreet stitches
Turned-in edge, machine sewn The fabric-covered perimeter fits comfortably beneath the presser foot Enclosed raw edges with a visible stitching line
Serged or overlocked edge The pad will be hidden, or exposed overlocking is acceptable Visible thread loops around the perimeter

Step 1: Check the Pad’s Position and Lay Out the Bias

  1. Place the uncovered pads inside the garment and check their position while wearing it or using a dress form. Respect any front, back, left, or right markings.
  2. Mark the line on each pad that follows the garment’s shoulder seam. This gives you a consistent reference for the fabric layout.
  3. Find the cover fabric’s lengthwise grain, which runs parallel to the selvage.
  4. Position the pad so its marked shoulder-seam line lies on the fabric’s bias.

Bias-cut woven fabric has enough give to settle over the pad’s rounded surface. Do not stretch it tightly during fitting: the aim is a smooth cover, not a compressed pad.

Keep the pads identified if they are shaped differently for the left and right shoulders.

Step 2: Wrap the Fabric and Anchor the Underside

  1. Fold a generous piece of fabric with its wrong sides together, keeping the pad’s shoulder-seam reference aligned on the bias.
  2. Slip the pad between the layers. Position the fold along an edge of the pad that the fabric can wrap without pulling; on a typical semicircular pad, this is usually the straighter edge.
  3. Check that the fabric reaches around both faces with surplus beyond the remaining perimeter. Cut away the unused yardage, leaving a roomy folded blank.
  4. Open the upper fabric layer like a book, leaving the pad resting on the lower layer.
  5. Support the pad in its natural curve and smooth the lower fabric against its underside.

The underside may be slightly hollow. Fabric stretched straight across that hollow can sag or form a pocket rather than following the pad.

Secure it with loose hand tacks along the pad’s center line, catching the cover and the pad’s surface. Keep the stitches relaxed enough that they do not create dimples on the opposite side.

Step 3: Make the First Contour Cut

  1. Keep the upper fabric layer folded out of the way.
  2. Trim the lower fabric around the pad’s open perimeter, leaving approximately 3/8 inch (1 cm) beyond the pad itself.
  3. Leave the connecting fabric fold intact.

This allowance supplies the fabric needed for the enclosed edge. Cut with the pad supported in its curved shape rather than pressing it flat against the table.

Where the contour turns sharply, run loose gathering stitches through the allowance. Draw them up only enough to help the fabric turn smoothly; you want eased fullness, not visible gathers.

Step 4: Shape the Upper Cover and Turn In the Edges

  1. Fold the upper fabric back over the pad, with the fabric’s right side facing outward.
  2. Smooth it over the raised surface.
  3. Trim the upper fabric with approximately 3/8 inch (1 cm) beyond the pad’s edge.
  4. Turn both raw allowances inward by about 1/4–3/8 inch (7–10 mm), enclosing the cut edges between the layers.
  5. Bring the folded edges together and pin or baste them in place.

A thick pad needs more fabric over its raised face than a flat outline alone would suggest.

Finger-press the folds rather than ironing the assembled foam pad. If fullness collects around a curve, redistribute it along the allowance before stitching. A pronounced pleat usually means the fabric needs reshaping, not a tighter seam.

Step 5: Stitch Around the Contour

Sew approximately 5/64 inch (2 mm) from the folded edge, catching both cover layers. Keep the stitching relaxed enough to preserve the pad’s curve.

For hand sewing:

  1. Use neat running stitches through both folded edges.
  2. Keep checking that the lower fold is caught, especially around the tightest curves.
  3. Secure the thread at the end and bury the tail between the fabric layers.

For machine sewing:

  1. Test the stitching on folded scraps of the cover fabric.
  2. Use a straight stitch and guide the folded perimeter beneath the presser foot.
  3. Support the raised center beside the foot instead of forcing the whole pad flat.
  4. Secure the stitching ends.

Machine sewing is practical only when the perimeter feeds freely. If the foot must compress substantial padding or the fabric stops feeding, finish the edge by hand rather than forcing it through.

Remove temporary perimeter basting and pins. Leave the underside anchoring tacks in place if they are holding the cover against the pad.

Step 6: Fit and Attach the Covered Pads

  1. Cover the second pad with bias-cut fabric, shape the fabric around the pad’s curve, and stitch the folded edges.
  2. Position both covered pads inside the garment according to its pattern or intended shoulder shape.
  3. Temporarily baste them to the available shoulder and armhole seam allowances.
  4. Try on the garment and check the shoulders from the front, side, and back.
  5. Once the placement is right, secure the covers with loose hand tacks.

Catch the seam allowances rather than sewing through the visible outer fabric. The attachment should hold each pad in position while allowing the garment to move naturally.

Do not assume every pad’s straight edge belongs in the same place: set-in-sleeve and raglan pads have different shapes and placement needs. Remove temporary positioning stitches and all pins after the permanent tacks are secure.

Quick Serged Covers and Dress-Form Pads

Quick serged covers finish garment pads with visible overlocking, while dress-form padding changes a form’s shape for fitting.

Making a Quick Serged Cover

A serged cover skips the turned-in edge. It is useful inside lined garments or wherever visible overlocking will not spoil the finish.

  1. Choose fabric and position the pad’s shoulder-seam line on the fabric’s bias.
  2. Fold the fabric around the pad, wrong sides together, leaving enough surplus to cover both faces without compression.
  3. Support the pad’s curve and smooth the fabric over it. Add loose underside tacks if the fabric bridges across the hollow.
  4. Trim the open perimeter, leaving a fabric margin wide enough for the serger to stitch without entering the padding.
  5. Baste the fabric layers together within that margin, then remove pins from the stitching path.
  6. Serge the open perimeter through the cover fabric, keeping the pad clear of the knife and needles. Do not flatten the pad to make it feed.
  7. Thread the finished chain tail back through the overlocking to secure it, then trim the excess tail and remove visible basting.

If the pad cannot stay clear of the serger’s working parts, use an enclosed, hand-sewn edge instead.

To install the finished pads, baste them into position, try on the garment, and secure their covers to the shoulder and armhole seam allowances with loose hand tacks. Remove the temporary stitches and pins once the shoulders sit correctly.

Choosing and Covering Dress-Form Padding

Dress-form shoulder padding serves a different purpose from pads sewn into clothing: it changes the form’s shape for fitting.

When choosing padding for this use, Fabulous Fit® Shoulder Pads are designed by the maker to increase a dress form’s measurements by up to 3 inches. That figure describes their dress-form fitting purpose, not the thickness to choose for garment shoulder pads.

These pads can be pinned to the form or held beneath a Fabulous Fit Stretch Cover. If you use that covering system, position the pads first, pull the stretch cover smoothly over them, and check that neither pad has shifted. Measure the dressed form before fitting your garment over it.

Check the Fit and Fix Cover Problems

A finished cover should look smooth while the pad keeps its original shape.

Signs of a Good Fit

  • The cover follows the raised top and the underside without a loose pocket.
  • The pad retains its curve rather than flattening into a stiff disk.
  • The perimeter has no exposed raw edges unless you deliberately chose overlocking.
  • Stitching does not pull dents into the padding.
  • The garment hangs smoothly over both shoulders.
  • No pins remain in the covers or attachment points.

Common Cover Problems

The underside sags. The fabric may be spanning the hollow instead of following it. Support the pad’s curve, smooth the fabric into place, and add relaxed center-line tacks. If there is substantial surplus, open the perimeter, refit the fabric, and resew the edge.

The pad curls or feels compressed. The cover or perimeter stitching is too tight. Unpick the affected section and release the tension. If the blank is too small, cut a roomier one.

The edge has bulky folds. Open the affected section and redistribute the fullness with loose easing stitches. Turn the allowances inward smoothly and resew without trapping a pleat.

A ridge shows through the garment. Check the uncovered pad’s shape and thickness as well as the cover seam. A bulky fabric or misplaced pad can remain visible even when the stitching is tidy.

The garment puckers near the attachment stitches. Release the tight tacks, let the garment settle over the pad, and attach it again without pulling the shell fabric toward the padding.

After any adjustment, the shoulders should still move and hang naturally.

Frequently Asked Questions

What Needle Should I Use to Machine-Sew Shoulder-Pad Covers?

Choose the machine needle for the cover fabric and the folded layers it must penetrate, not simply for the garment’s outer fabric. A fine universal or sharp needle is a sensible starting point for lightweight woven covers. Test it on folded scraps; skipped stitches or snagging mean the needle and fabric combination needs attention before you sew the cover.

Can I Embroider Shoulder-Pad Covers?

Yes, embroider the cover fabric while it is still flat, before cutting and fitting it around the pad. Keep the design light and away from the folded perimeter so dense stitching and bulky knots do not interfere with shaping. For sheer garments, check whether the embroidery will show through the outer fabric.

Can I Wash Fabric-Covered Shoulder Pads?

Only if both the padding and the cover fabric are washable. A washable fabric cover does not make a dry-clean-only or otherwise nonwashable pad suitable for laundering. If the pad and garment need different care, remove the covered pads before washing and reattach them after the garment is dry.