How to Hand Sew an 18-Inch Separating Zipper

18 inches is a standard separating-zipper length, and you can sew one entirely by hand by basting the tapes, backstitching them in place, and topstitching each edge about 1/8 inch from its fold. This method works for a cardigan, costume, pouch, project bag, or any opening made from two separate fabric edges. The key is to position both zipper halves while they are aligned, then sew every pass in the same direction.

Use these measurements and checks while choosing and positioning the zipper.

What You’re Checking What to Use
Choose a zipper length that suits the item you are making and your body proportions. 18 inches, measured from the top of the slider to the bottom stop
Common retail zipper lengths 7 to 22 inches
Temporary basting stitches About 1/4 inch long
Final topstitching line About 1/8 inch from the folded opening edge

Understanding Separating Zippers

A separating zipper is the kind that comes apart completely at the bottom. One tape ends in an insertion pin, and the other has a box that receives the pin. Jackets, hoodies, removable cushions, and fully opening bags often use this style.

Buy a separating zipper rather than a closed-end zipper. Standard zipper lengths commonly run from 7 to 22 inches, and zipper length is measured from the top of the slider to the bottom stop, as explained in New Mexico State University’s zipper guide.

Before sewing, identify the zipper’s right side: it is the side where the slider and pull are meant to show. For an exposed separating zipper, flip the zipper tape and seam allowance edges to the inside, then topstitch the zipper edges.

A separating zipper is easiest to install before adding a lining, facing, collar, or hem that would cover the zipper ends. If your project already has those layers, open the necessary stitching so you can reach the zipper tape cleanly.

How to Hand Sew a Separating Zipper

A separating zipper is basted behind folded opening edges, then secured with small backstitches from the lower edge toward the top.

Step 1: Prepare the Opening and Supplies

Gather the zipper, matching all-purpose sewing thread, a hand-sewing needle, pins or clips, fabric-marking tool, scissors, a thimble if you use one, and a sewing gauge or ruler.

Finish or press the two raw opening edges before adding the zipper. For a simple unlined project, turn each opening edge to the wrong side and press it so the fold is even from top to bottom. For a lined or faced project, leave enough access to stitch the zipper tape before enclosing the inside.

Mark matching points on both opening edges. Mark the hemline, neckline, waist seam, color-block seam, pocket edge, or any other horizontal detail that must line up when the zipper is closed.

Lay the project flat with the wrong side facing up. The zipper’s separating box and insertion pin belong at the lower edge of the opening.

Step 2: Position and Baste the First Zipper Tape

Close the zipper completely. Place one zipper tape behind its folded fabric edge, with the zipper’s right side against the garment’s wrong side. The zipper teeth should sit immediately beyond the fold so they will show from the outside, while the tape extends onto the seam allowance inside.

Align the lower zipper box with the bottom of the opening. Match any horizontal marks you made, then pin or clip the tape in place without piercing the teeth.

Baste the zipper tape to the folded edge and seam allowance. Keep the temporary basting stitches about 1/4 inch long; this makes them easy to remove while holding the tape securely enough for fitting. The University of Kentucky Cooperative Extension 4-H sewing guide uses this stitch length for hand basting.

Start at the lower edge and work toward the top. This direction matters for every later pass as well.

Step 3: Align and Baste the Second Tape

With the zipper still closed, place the second zipper tape behind the opposite folded edge. Match the bottom edges first, then align every marked horizontal seam or design detail.

Once the tape is pinned, unzip the zipper so the two halves can lie flat. Baste the second tape from the lower edge toward the top, just as you did on the first side.

Sew every basting, permanent-stitching, and finishing pass in the same direction, usually from the hem or lower edge toward the neckline or upper edge. Sewing one side upward and the other downward can pull the fabric differently on each side and leave the zipper edges mismatched.

Close the zipper for a quick test before making anything permanent. If the pull catches, remove and reposition that section before continuing.

Step 4: Hand Topstitch the Zipper in Place

Thread your needle with a length of thread you can handle comfortably. Hide the starting knot inside the seam allowance near the lower edge.

From the right side of the project, work a line of small backstitches through the folded fabric edge and zipper tape. Keep the stitching line about 1/8 inch from the fold. This topstitching secures the tape and creates a neat, intentional line on the outside.

To make a backstitch, bring the needle out ahead of the previous stitch, then insert it back into the end of the previous stitch before bringing it forward again. Keep the stitches even, and avoid stitching through the zipper teeth or coil.

Work from bottom to top on the first zipper half. Remove the basting as you reach it rather than pulling out all of the temporary thread at once. Repeat on the second tape, again starting at the lower edge and sewing toward the top.

I use a sewing gauge here rather than estimating the topstitching line, because the narrow distance from the fold is much easier to keep even.

When about 3 inches of thread remain, take a final backstitch. On the inside, pass the needle beneath nearby stitches twice, pull snugly, and trim the thread close to the fabric.

Step 5: Secure the Top and Bottom Ends

At the upper edge, enclose the zipper tape end inside a facing, collar, binding, or turned edge if your project has one. Hand slipstitch that finishing layer to the seam allowance and zipper tape, keeping the inside finish smooth and secure.

At the lower edge, add support only if needed. Tack only the outer edge of the zipper tape to the seam allowance or hem allowance if it needs extra support. Never stitch through the box, pin, or the gap where the pin must enter the box.

For an unlined item, neatly secure any exposed tape end by folding it to the wrong side and whipstitching it to the seam allowance. For a lined item, hand stitch the lining to the zipper tape on the inside after the zipper has been tested.

Step 6: Test, Press, and Finish

Insert the pin fully into the zipper box and zip the zipper from bottom to top. Check that:

  • The top and bottom edges meet evenly.
  • Horizontal seams and design lines align.
  • The slider moves freely without catching thread.
  • The folded fabric edges sit flat without gaps or overlap.
  • The zipper tape is fully caught by the topstitching.

Press the fabric beside the zipper if needed, but avoid pressing directly on plastic teeth, a coil, or the zipper pull.

Using a Separating Zipper on a Bag or Lined Project

A separating zipper can work on a bag when you want the opening to come fully apart, such as on a removable cover, travel case, or flat-opening project pouch. It is less useful for a standard tote bag, where a closed-end zipper usually keeps the two sides connected.

For an unlined bag, finish the top edge of each bag panel first. Place one zipper tape behind the finished top edge of the front panel and the other behind the finished top edge of the back panel. Baste and hand topstitch each tape separately, keeping the zipper closed while you align the ends and then opening it to sew each tape flat.

For a lined bag, attach the zipper to the exterior first and test the zipper fully. Then fold the lining’s upper edge inward and slipstitch it to the inside edge of the zipper tape.

If the zipper runs across the top of a bag, open it before turning the bag right side out or before stitching any final seam that would trap the zipper pull.

Shortening a Too-Long Separating Zipper

The best choice is to buy the correct length. If you must shorten a separating zipper, shorten it only from the top. The bottom box and insertion pin make the zipper separate and reconnect.

Shortening a Coil Separating Zipper by Hand

This hand-sewn stop method is for a coil zipper, not a molded-tooth or metal-tooth zipper. Confirm that your zipper has a continuous coil before using it.

  1. Close the zipper and mark the new top-stop position on both zipper tapes. Measure from the bottom stop so both sides end at the same height.
  2. Thread a needle with strong matching thread and stitch around the coil and through the tape at the marked position.
  3. Wrap the thread around the coil 12–15 times, as Peekaboo Pattern Shop suggests, to build a firm new stop. Make an identical stop on the other zipper half.
  4. Close the zipper and pull the slider to the new stops. Confirm that the pull stops before reaching the cut area and that both sides end evenly.
  5. Trim the excess tape above the new stops.
  6. Fold the raw tape ends to the wrong side and whipstitch them down, or cover them inside a facing, collar, binding, or hem.

Check the zipper maker’s instructions before making a sewn replacement stop on a coil zipper. Choose the correct length, or install replacement top stops made for the zipper type.

Why the Usual Bar-Tack Method Does Not Suit a Separating Bottom

A conventional closed-end zipper can be shortened by sewing a bar tack across the zipper at the desired length, sewing a second bar tack about 1/2 inch below the first, and cutting the zipper about 1/2 inch below the lower bar tack. Finish the cut tape edge by folding or binding it so it does not fray.

A separating zipper needs its bottom box and insertion pin to separate and reconnect.

Checking Fit and Fixing Problems

Most problems are easiest to correct while the tape and seam allowances are still accessible.

Problem Likely Cause Fix
Zipper pull catches or will not close Stitches are too close to the teeth or coil Remove stitches in the affected area and resew farther from the teeth
Seams do not align when zipped The two sides shifted during basting or were sewn in opposite directions Remove the affected stitching, align with the zipper closed, baste again, and sew both sides from bottom to top
Fabric ripples beside the zipper Fabric or tape was stretched while stitching Press the fabric flat, remove the rippled section, rebaste without pulling, and resew
Tape shows unevenly along the opening Folded edges were not positioned consistently Re-press the fold and resew the uneven section
Slider runs off a shortened coil zipper The replacement stop is too loose or too high Rebuild the thread stop before trimming further tape

A final successful check is simple: zip the project closed, lay it flat, and make sure the opening edges are smooth, the pull reaches both ends, and the zipper separates and reconnects without resistance.

Frequently Asked Questions

Is it possible to hand sew a separating zipper?

Yes, you can hand sew a separating zipper. Close it to align both tapes, then unzip it so the halves lie flat for stitching. Hand sewing is a practical option when you do not have a zipper foot, are working with a small project, or want more control over thick or delicate fabric. Baste the tape first, then use firm backstitching through the folded edge and zipper tape.

How do I attach a zipper after the two halves have separated?

Attach one zipper tape first, then close the zipper to position the second tape so the top, bottom, and any horizontal seams match. Unzip the halves to baste the second side with stitches about 1/4 inch long, then permanently stitch both tapes from the lower edge toward the top.

How do I hand stitch a zipper on a bag?

Finish the bag’s opening edges, place the zipper tape behind those edges with the teeth facing outward, and baste one tape to each side. Hand topstitch through the bag edge and zipper tape, then test the zipper before sewing in the lining or final inside finish.

Can I turn a regular zipper into a separating zipper?

No. A regular closed-end zipper lacks the insertion pin and box that allow a separating zipper to come apart and reconnect. You can shorten a separating zipper from its top when appropriate, but cutting off its bottom hardware will not create a usable separating closure.