How to Sew a Drawstring
A sewn drawstring is a cord or fabric tie that runs through a stitched casing, letting you gather a bag, waistband, hood, or neckline. The key is to make a smooth channel with secure openings, then choose a drawstring that slides easily without being bulky. This guide covers a basic casing, fabric drawstrings, drawstring bags, hoodies, waistbands, and safe finishing.
How a Drawstring and Casing Work
A drawstring has two parts:
- The drawstring is the cord, ribbon, twill tape, or sewn fabric tube that pulls the opening closed.
- The casing is the fabric tunnel sewn into the garment or bag.
The casing can be made by folding over a top edge, attaching a separate strip of fabric, or sewing a channel into a waistband or hood. The exits can be buttonholes, small gaps left in a seam, or openings at the side seams of a bag.
A drawstring works best when it moves freely through the casing while the casing itself stays flat and firmly stitched.
Before sewing, choose the drawstring material. Pre-made cord is the quickest option. Sewn fabric drawstrings coordinate beautifully with a garment or embroidered project bag, while twill tape and narrow ribbon are easy to thread and less likely to twist.
How to Sew a Basic Drawstring Casing
Choose the construction that matches what you are making before you sew the channel.
| Project | Best Casing Construction | Drawstring Choice |
|---|---|---|
| Elastic-free waistband | Folded waistband casing with center-front exits | Cord, twill tape, or fabric tie |
| Hoodie or neckline | Casing sewn into the hood or neck edge | Cord or knit fabric tube |
| Gift bag | Folded top casing | Cotton cord, ribbon, or twill tape |
| Small project bag | Separate channels on the front and back | Two cords for a double-draw closure |
| Gathered pouch | Fabric strip sewn as a casing | Cord or narrow ribbon |
Step 1: Mark the Drawstring Exits
- Decide where the drawstring will emerge before sewing the casing closed.
- For a waistband or hood, place the exits at the center front. Use two buttonholes, two reinforced openings, or a small gap in the center-front seam.
- For a bag, leave the casing open at the side seams so the cord can enter and exit.
- Finish the opening edges before the casing is stitched down. A buttonhole is neat for garments; a small seam gap is often simpler for a bag.
A drawstring opening needs reinforcement because the cord repeatedly rubs against it. Stitch around seam gaps or add a small square of interfacing behind buttonholes on lightweight woven fabric.
Step 2: Fold or Attach the Casing
- Finish the raw top edge if the fabric frays.
- Fold the top edge to the wrong side by the casing depth required for your cord, leaving enough room for the cord to pass without catching.
- Press the fold well. A crisp press keeps the casing even and makes it much easier to stitch.
- If you are using a separate casing strip, finish its short ends first, then stitch its long edges to the wrong side or right side of the project as your design requires.
For a waistband, make sure the casing is wide enough that the drawstring will not bunch the fabric as it moves. For a hood, keep the channel consistent around the curve so the cord does not snag at the side seams.
Step 3: Stitch the Casing
- Stitch close to the lower folded edge of the casing.
- Stop and backstitch before reaching any opening that must remain clear.
- Sew slowly across thick seam allowances, especially at side seams and center seams.
- Check inside the casing for loose threads, pins, or raw seam allowances that could catch the cord.
If you are sewing a casing through several layers, guide the fabric evenly rather than pulling it from behind the needle. Pulling can stretch one layer and leave a rippled channel.
Step 4: Thread and Finish the Drawstring
- Attach a safety pin, bodkin, or small loop turner to one end of the drawstring.
- Feed it through one casing opening, bunching the fabric along the tool as you work.
- Keep hold of the other end so it cannot disappear into the channel.
- Pull the drawstring through both exits and even up the tails.
- Finish the ends with knots, cord stops, folded-and-stitched fabric ends, or small end caps suited to the material.
- Pull the drawstring open and closed several times. It should gather the fabric without catching or pulling the casing stitches.
How to Make a Fabric Drawstring
A fabric drawstring can be sewn from woven fabric or knit fabric. Woven fabric is crisp and stable; knit fabric makes a soft, stretchy hoodie-style tie.
Topstitched Woven Drawstring
A topstitched woven drawstring is a no-turn method that is a good choice when a narrow fabric tube would be difficult to turn right side out.
The topstitched woven option begins with a strip 1.5 inches (3.81 cm) wide, cut to the needed length. Press each raw short end under 3/8 inch (1 cm), then press the long raw edges to the wrong side so the strip forms a neat, narrow band.
- Stitch the folded short ends closed.
- Topstitch down both long sides, sewing about 1/8 inch (0.31 cm) from each edge.
- Thread the finished drawstring through the casing with a safety pin.
- Tie knots in the ends if you want a simple finish, or fold and stitch the ends for a flatter look.
This method produces a durable drawstring with visible topstitching and no bulky seam allowance inside a tube.
Knit Tube Drawstring for a Hoodie
A knit tube drawstring is soft enough for a hoodie and can match the garment fabric exactly. Choose knit-strip dimensions that will fit the hood casing and provide the desired finished length.
For its Page Hoodie, Chalk and Notch uses two knit strips 25 inches (63.5 cm) long by 1.25 inches (3.2 cm) wide.
- Fold one strip lengthwise with right sides together.
- Sew across one short end, pivot, and sew down the long edge, leaving the other short end open.
- Turn the tube right side out. Repeat for the second strip.
- Overlap the two open ends by 1 inch (2.5 cm), pin them, and sew them together to form one long drawstring.
- Attach a safety pin to one finished end, thread the drawstring through the hood casing, and check that the join moves smoothly through the channel.
Use a ballpoint or stretch needle for knit fabric so the seam can flex without popping.
Woven Tube Drawstring With a Safety Pin
For a fuller woven-fabric drawstring, cut a strip to the length your project needs. Chalk and Notch’s woven safety-pin method uses a strip 1.5 inches (3.81 cm) or 1.75 inches (4.44 cm) wide.
- Fold the strip lengthwise with right sides together.
- Shorten the stitch length and sew the long edge with a 3/8-inch (1 cm) seam allowance.
- Trim that seam allowance in half to reduce bulk.
- Push a safety pin through one layer at an open end, turn the pin into the tube, and work it through until the tube is right side out.
- Press the drawstring flat and finish the ends before threading it through the casing.
For an elastic-back drawstring, make two fabric drawstrings with one enclosed outer end and one raw inner end. For an elastic-back drawstring, overlap each raw drawstring end onto the elastic by about 1/2 inch (1.27 cm), then secure it with a zigzag stitch. Thread the free ends through the front casing openings, stretch the elastic gently, and make sure both drawstrings pull evenly.
How to Sew Drawstring Bags
Drawstring bags are useful for embroidery hoops, floss projects, small gifts, and travel stitching supplies. You can make one with separate channels for a double-draw closure or with a folded top casing and one continuous cord.
Separate-Channel Drawstring Bag
A separate-channel bag closes from both sides, making a tidy gathered top. A compact bag layout uses two body panels measuring 11.5 by 6.5 inches and two channel rectangles measuring 6.5 by 1.5 inches; confirm the exact pieces in your own bag cutting layout before cutting.
- Cut the two body panels and the two channel pieces.
- Finish the raw edges of the body panels if the fabric frays.
- Press the short ends of each channel piece to the wrong side, then press the long edges under.
- Position one channel across the upper right side of each body panel. Stitch along the upper and lower long edges of each channel, leaving both channel ends open.
- Place the body panels right sides together. Sew the side seams only below the channels, leaving the channel ends open as cord exits. Sew the bottom seam.
- Turn the bag right side out and press it.
Thread two cords for a double-draw closure. Feed the first cord through the front channel and then through the back channel so both ends emerge on one side. Feed the second cord from the opposite side in the same way. Knot the ends of each cord, then pull both pairs to close the bag.
Fold-Over Casing Gift Bag
A fold-over casing is a simple choice for a gift bag or a larger fabric storage pouch.
- Cut two bag panels or fold one larger piece of fabric into the bag shape. Finish raw edges that are likely to fray.
- With right sides together, sew the bottom and side seams. For this bag layout, stop each side seam about 4 inches from the top so the upper portions remain open for the casing exits; confirm the exact stopping point in your bag pattern’s casing instructions.
- Press the unsewn side-seam sections open and stitch their seam allowances down so the openings are tidy and strong.
- Fold the top raw edge 1/4 inch to the wrong side and press. Fold the top down again to the point where the side opening begins, then stitch around the bag to form the casing.
- For a frilled top edge, sew an optional second line about an inch above the first casing seam.
- Thread a cord through one side opening, around the casing, and back out through the same opening. Knot both ends securely.
Pull the cord to make sure the casing gathers evenly and the side opening does not pull apart.
How to Sew Drawstrings in Hoodies and Waistbands
For a hoodie, sew the hood seam and finish the hood edge before making the casing. Create the two center-front exits before stitching the casing down, then thread the drawstring after the hood is attached to the garment. A fabric tube, cotton cord, or flat twill tape all work well, but avoid a drawstring so thick that it distorts the hood edge.
For a drawstring waistband, sew the waistband casing while leaving the center-front exits open. Thread the drawstring after the waistband is fully attached, then test the fit while the garment is on. If you are combining elastic and a drawstring, attach the elastic securely before closing the final casing section.
Do not use free-moving drawstrings in the hood or neck area of children’s outerwear. The U.S. Consumer Product Safety Commission advises removing them from children’s jackets, sweatshirts, and similar garments. To reduce the drawstring hazard, the CPSC urges you to remove hood and neck drawstrings from children’s garments; alternatively, sew a seam through the drawstring at the middle so neither end can pull out, and cut the ends short enough to close the garment.
Check Fit, Strength, and Safety
Before calling the project finished, check these points:
- The drawstring moves from one exit to the other without catching.
- Both drawstring tails are even when the opening is relaxed.
- The casing lies flat rather than twisting around the cord.
- The cord cannot pull through a casing exit.
- Knots, stitched ends, or cord stops are secure.
- Bag side openings and garment buttonholes show no loose stitches.
- The drawstring does not snag on seams inside the channel.
If the drawstring sticks, remove it and inspect the casing. A trapped seam allowance, a loose thread, or a channel that narrows at a side seam is usually the problem. Trim stray threads, press bulky seam allowances flatter, and rethread the cord.
Frequently Asked Questions
How do I make a drawstring for a hoodie?
A sewn knit tube makes a soft hoodie drawstring that matches the garment. Cut two strips 25 inches (63.5 cm) long by 1.25 inches (3.2 cm) wide, sew and turn each tube, then join the open ends with a 1-inch (2.5 cm) overlap. Thread the finished tube through the hood casing with a safety pin.
How do I sew a drawstring neck?
Sew a casing along the neckline or hood edge, leaving two reinforced exits at the center front. Thread the cord after the casing is complete and test that it gathers evenly. For children’s clothing, avoid hood and neck drawstrings; if retaining one in an existing garment, stitch through it at the center so the ends cannot pull out.
How do I sew a drawstring waistband?
Make buttonholes or reinforced openings at the center front before you stitch down the waistband casing. Sew the casing, thread the cord through both openings, and finish the cord ends with knots or stitched folds. The channel must be wide enough for the drawstring to move without twisting the waistband.
How do I sew a drawstring backpack?
Sew two channels across the upper front and back of the bag, leaving both ends of each channel open at the sides. Sew the body panels together below the channels, then thread two cords in opposite directions so each cord exits from one side. Pulling both cords closes the backpack-style top.
Why does my drawstring keep disappearing into the casing?
The free end was not secured while the other end was threaded through. Pull the cord back out with a safety pin or bodkin, then clip, pin, or temporarily knot the free end outside the casing before rethreading. Finishing the cord ends with knots or stitched ends also helps prevent this problem.
