How to Make Your Own Saddle Pad

Four felted-wool pieces and two brocade facing pieces make a sewn saddle pad when you use a pad as the pattern. The key is to choose the construction first, quilt the layers so they cannot shift, finish the spine and outer edge securely, and test the completed pad without asking it to correct a saddle-fitting problem.

A homemade pad is best for creating a custom color, fabric combination, or shape, not for changing how the saddle fits your horse.

What a Homemade Saddle Pad Can Do

A saddle pad creates a clean, stable layer between the saddle and the horse. It can protect the saddle from sweat and dirt, hold its shape under normal use, and add modest cushioning depending on the materials you choose.

It cannot make a too-narrow, too-wide, unstable, or poorly balanced saddle fit correctly. The saddle should sit level and leave appropriate clearance at the withers and along the spine before you depend on the pad.

This tutorial makes a shaped pad for an English or dressage-style saddle. For a western pad, use a western pad that already fits as the template; the outline, spine shape, and load-bearing areas are different.

Choose the Saddle Pad Construction Before You Cut

Choose the construction before you decide on layer counts, quilting, or edge finishing.

Use this comparison to select a build that suits the materials you have and the job the pad needs to do.

Construction Typical Materials Best Use
Quilted fabric pad Cotton or cotton-blend outer fabric with quilt batting A light, decorative pad with a traditional quilted look
Felted-wool pad Felted wool backing with a brocade or sturdy cotton facing A structured pad with natural-fiber backing and a custom top fabric
Foam-core pad Cotton and flannel around a foam core chosen to preserve wither clearance and saddle balance A thicker, more structured design that needs careful quilting and secure edge binding
Pulled-wool pad Wool top pulled through a foundation with specialized tools A traditional wool surface rather than a sewn quilted pad

For a first project, the felted-wool-and-brocade construction is approachable because the layers are visible, easy to trace, and straightforward to quilt. It also gives you a finished pad with a polished spine seam rather than a flat rectangular blanket under the saddle.

A pulled-wool pad is a different craft from sewing a layered pad. It uses wool top and dedicated pulling tools; a pulled-wool starter kit is useful if that is the style you want to make.

How to Sew a Felted-Wool Saddle Pad

Gather a saddle pad that fits your horse and saddle well, felted wool, brocade or sturdy cotton for the top, matching thread, tailor’s chalk, fabric scissors, pins or clips, edge binding, and a sewing machine. Add nonstretch fabric or webbing if you want billet or girth straps.

Step 1: Make a Reusable Pattern From a Pad That Fits

  1. Lay the existing pad flat and identify its center spine line.
  2. Fold the pad along that line, or trace one side profile onto pattern paper. Your pattern should represent one side of the finished pad.
  3. Mark the front, rear, spine edge, and underside so you do not reverse the shape while cutting.
  4. Transfer any strap placement from the existing pad if you plan to add straps.

Trace the working pad accurately rather than copying only a shape you like. The front contour, spine length, and drop below the saddle flap all affect whether the finished pad stays in place.

Step 2: Cut the Wool and Facing Pieces

If you are making your own felted wool from coat-weight wool, wash it on hot and dry it before cutting so the fabric has already shrunk and tightened.

  1. Place the one-side pattern on the felted wool and cut 4 wool pieces.
  2. Lay a wool piece on the brocade or top fabric and cut 2 brocade pieces.
  3. Cut the brocade slightly larger than the wool around the outer edge. Quilting pulls fabric inward, and the extra facing fabric gives you room to trim a clean final outline.
  4. If the top fabric has a directional print, check that the design runs correctly on each side. Cut a true left and right piece so lettering, flowers, stripes, or motifs do not end up upside down or mirrored unintentionally.

You will have two quilted panels: each panel uses one brocade facing over two felted-wool layers.

Step 3: Mark and Quilt the Two Panels

  1. Stack one brocade piece right side up over two wool pieces, aligning the spine edge carefully.
  2. Smooth the layers on a flat work surface and pin or clip them securely, especially around the curved front and rear edges.
  3. With tailor’s chalk, mark diagonal quilting lines every 2 inches across the brocade.
  4. Stitch along the marked lines, keeping the layers flat as they feed through the machine. Work steadily and stop to smooth the wool if it begins to creep or wrinkle.
  5. Repeat for the second panel.
  6. Trim the quilted panels to match the wool shape, leaving the two panels as mirrored sides.

I use a basic sewing machine to stitch a small layered scrap first, because it lets me adjust thread tension before quilting the full pad.

Quilting matters because it prevents the wool layers from sliding, bunching, or sagging away from the facing fabric. Keep the quilting pattern simple and even; the pad needs to lie flat more than it needs an elaborate design.

Step 4: Join and Cover the Spine Seam

  1. Put the brocade sides of the two quilted panels together, matching the spine edges from front to rear.
  2. Use a wide zigzag stitch close to the spine edge to join the panels. Open the pad so the wool sides face down and the brocade sides face up.
  3. Cut a backing-fabric strip about 2 inches wide and as long as the spine of your pad.
  4. On the wool side, place the strip over the spine seam and straight-stitch it about 1/2 inch from the seam edge.
  5. Fold the loose edge of the strip under about 1/2 inch, then topstitch it flat to cover the raw seam and reinforce the spine.

Finish the brocade side of the spine so the visible seam looks intentional:

  1. Cut a brocade strip 2.5 inches wide and the length of the pad.
  2. Lay it with one long edge about 3/4 inch inside the seam and sew that edge.
  3. Fold the loose edge under, pin it flat over the seam, and topstitch it down.

This two-sided spine finish protects the seam, covers stitching, and gives the pad a clean raised center that follows the horse’s back.

Step 5: Bind the Outer Edge and Add Straps

  1. Trim the outer edge of the pad so both quilted panels match exactly.
  2. Apply durable binding around the full perimeter, enclosing every raw wool and brocade edge. Ease the binding around curves instead of pulling it tight.
  3. Overlap and secure the binding ends at a discreet point near the rear of the pad.
  4. If you want billet or girth straps, cut them from a nonstretch material, position them where they sit outside the saddle’s pressure-bearing area, and reinforce their attachment with multiple stitching passes.
  5. Check that no raw edges, loose thread ends, sharp hardware, or bulky strap seams will lie against the horse.

Straps help keep the pad tidy while tacking up.

Step 6: Test the Finished Pad Before Regular Use

  1. Place the clean, dry pad on the horse’s back with the spine seam centered.
  2. Set the saddle on top and lift the pad into the gullet so the fabric is not pulled tight over the withers.
  3. Check that the pad extends beyond the saddle panels, lies smoothly on both sides, and does not fold under the saddle.
  4. Girth up normally and look from the front, side, and rear for twisting, creeping, or uneven hanging.
  5. After a controlled first ride, remove the saddle and inspect the pad and the horse’s back. Stop using the pad if it shifts, develops hard folds, creates uneven pressure marks, or seems to cause soreness.

How to Check Saddle Pad Fit and Function

Once the sewing is finished, confirm that the pad works with your tack.

  • The spine seam should follow the horse’s centerline without pulling down onto the withers.
  • The saddle panels should rest on the pad, not on a thick seam, strap attachment, or lump of quilting.
  • The pad should remain smooth after mounting and riding.
  • The edge binding should not curl inward beneath the saddle.
  • The wool layers should remain evenly distributed after use.
  • The saddle should still look balanced from the side.

If you see a repeated wet spot, compressed ridge, shifted pad, or an area where the horse reacts to grooming or saddling, stop treating it as a sewing issue. Consult a qualified saddle fitter or veterinarian when needed.

Care for a Handmade Saddle Pad

Remove loose hair, dust, and dried sweat when the pad comes off the horse. Let the pad dry completely before storing it so moisture does not remain trapped in the wool layers or binding.

Inspect the quilting, spine covering, edge binding, and straps regularly. Repair loose stitching before riding again.

Spot-clean brocade or cotton facing carefully, especially if it has a decorative weave or finish. Felted wool can shrink or become stiffer with aggressive washing, so avoid treating the finished pad like an ordinary laundry item. Keep the pad flat during storage rather than folding it sharply along the spine.

Frequently Asked Questions

What type of fabric should be used in making a saddle pad?

Use a sturdy, smooth-facing fabric such as cotton, cotton blend, or brocade for the visible side, paired with materials that hold their shape underneath. Felted wool is a good backing choice for a structured natural-fiber pad, while quilt batting makes a lighter decorative pad. Avoid slippery fabrics, loose knits, and materials that shed, stretch, or compress into ridges.

What is the best thickness for a saddle pad?

There is no single best thickness because the saddle must fit the horse before the pad is added. A felted-wool design can use two wool layers per side, while foam-core pads use a foam center selected to preserve wither clearance and saddle balance. Choose the thinnest construction that gives the structure and protection you need without reducing wither clearance or changing saddle balance.

Can you use a blanket as a saddle pad?

Do not use an ordinary blanket by itself as a saddle pad. It can bunch, shift, form folds, and create uneven pressure beneath the saddle. A sturdy wool blanket can be used as material for a pad only after it is cut to shape, stabilized with quilting, securely bound, and tested under the saddle.

How do you make a mini horse saddle pad?

Make a mini horse saddle pad by tracing a pad that already fits the mini saddle and horse, then scaling the layers to that exact template rather than guessing from a full-size horse pad. Keep the spine centered, preserve wither clearance, and avoid bulky seams where the smaller saddle panels will rest. Test the pad with the saddle before riding or driving.

How is a pulled-wool saddle pad different from a sewn saddle pad?

A pulled-wool saddle pad has wool top pulled through a foundation, while a sewn pad uses stacked fabric layers held together with quilting and binding. The pulled-wool process needs specialized tools and wool top, whereas the sewn felted-wool method uses cut layers and a sewing machine. Choose the method before buying materials, then trace a pad that already fits your horse and saddle.