How to Sew a Jersey T-Shirt Hem With an Overlocker

A jersey T-shirt hem is usually made by overlocking the raw edge, turning it up once, and securing that fold with a stretch-capable stitch. Your overlocker controls the curling edge neatly, while the final stitching lets the hem stretch when the shirt is pulled on. If you have only an overlocker, a flatlock or rolled hem can also create a finished hem, but they give a different look from the familiar ready-to-wear T-shirt hem.

What an Overlocker Does for a Jersey Hem

An overlocker, also called a serger, wraps thread around a cut edge while trimming and finishing it.

A standard overlock stitch does not usually create the two parallel lines seen on most store-bought T-shirts. Those are made with a coverstitch machine or a twin needle on a regular sewing machine. Still, an overlocker is valuable for a clean, durable single-turn hem, and it can make several hem styles by itself.

For a basic jersey T-shirt hem, overlock the raw edge first, turn it up once, and then secure the fold with a stretch-capable stitch.

Overlocking the raw edge before folding reduces edge curl and makes soft jersey easier to hold at an even depth.

How to Sew a Basic Jersey T-Shirt Hem With an Overlocker

Choose the finish that matches your equipment and the look you want before preparing the shirt.

Goal Best Method What You Need
Classic everyday T-shirt hem Overlock the edge, turn it once, then stitch the fold Overlocker plus regular sewing machine
Nearly hidden hem made on an overlocker Two-thread wide flatlock “blind” hem Overlocker capable of two-thread flatlock; blind-hem foot is helpful
Decorative wavy edge Three-thread rolled lettuce hem Overlocker with a rolled-hem setting
Very lightweight or curling jersey Overlock first, then use a single turned hem Overlocker plus a stretch-capable sewing-machine stitch

Step 1: Test the Jersey and Mark the Hem

  1. Cut or save a small scrap of the same jersey. Test every hem finish on this scrap before sewing the actual shirt.
  2. Stretch the test piece gently across the direction in which the T-shirt hem needs to stretch. The stitches should recover without popping or looking strained.
  3. Decide where the finished hem should sit, then mark that line evenly around the shirt. If you are shortening a ready-made shirt, leave enough fabric below the marking line to form the turn-up.
  4. Press the proposed hem fold lightly on the test scrap first. Some jerseys shine, flatten, or develop a visible press mark with too much heat.

Step 2: Overlock the Raw Hem Edge

  1. Thread your overlocker for its ordinary three- or four-thread overlock stitch, using the threading path and starting tensions recommended for your machine.
  2. Sew a test seam on the jersey scrap. The looper threads should meet at the cut edge rather than pulling noticeably to the right or wrong side.
  3. Overlock around the T-shirt’s raw lower edge. Feed the fabric without pulling it in front of or behind the presser foot.
  4. Use the knife only to remove an uneven edge or a very narrow amount of fabric. Cutting away too much can shorten the shirt beyond the hem line you planned.
  5. When you return to the starting point, overlap the beginning of the overlocking briefly. Chain off, pull the thread chain to the inside, draw it beneath the overlock stitches with a blunt needle, and trim the excess.

The overlocked edge should lie flat.

Step 3: Turn Up the Hem Once

  1. With the wrong side facing up, turn the overlocked edge toward the inside of the shirt along your marked hemline.
  2. Press the fold gently, working evenly around the shirt.
  3. Hold the fold with clips, pins placed away from the stitching path, or hand basting if the jersey is slippery.
  4. Keep the overlocked edge fully inside the folded hem. It should sit flat rather than roll toward the right side.

A double-folded hem can create unnecessary bulk, especially at side seams and on thicker T-shirt knits.

Step 4: Secure the Fold With a Stretch Stitch

  1. Set up a regular sewing machine with a stretch-capable stitch, such as a narrow zigzag, lightning stitch, or twin needle stitch. Test it on the prepared scrap with the same folded, overlocked edge.
  2. Sew from the right side of the shirt, close to the upper edge of the turned hem.
  3. Guide the shirt around the machine bed without pulling the jersey.
  4. At the end, overlap the beginning of the stitching slightly or secure the thread tails by pulling them to the inside and tying them neatly.
  5. Stretch the hem gently after sewing. If stitches pop or the fabric tunnels between them, remove the test stitching and adjust the stitch setup before hemming the shirt.

Press the completed hem from the wrong side through a press cloth if needed. The result should lie smooth and stretch comfortably.

Other Overlocker Hem Options

Two-thread wide flatlock and three-thread rolled lettuce hems create alternative overlocker finishes, from subtle stitched detail to a decorative ruffled edge.

Two-Thread Wide Flatlock “Blind” Hem

A two-thread wide flatlock gives you an overlocker-only hem with a subtle stitched appearance on one side and flatlock “ladder” threads on the other. It works best on a hem that is straight or only gently curved. It is also easier to sew before the T-shirt side seams are closed, when the hem can lie flat.

  1. Press the hem up to the wrong side.
  2. Fold the hem back outward so the fold forms a raised ledge for the overlocker to catch. The garment body and hem should lie in layers, with the fold positioned under the foot.
  3. Set up the machine for a two-thread wide flatlock according to its manual. Use the two-thread conversion and needle arrangement required by your model, and disengage or lock the knife if your machine’s flatlock instructions call for it.
  4. One sewing blog’s starting point on machines with comparable control scales is stitch length 4, stitch width 7.5, and differential feed 1.3. Confirm the exact arrangement in your overlocker manual and on a jersey test swatch, since dial scales and thread paths vary by model.
  5. Stitch along the fold, catching the hem ledge without cutting into the body of the shirt.
  6. Open the folded layers and pull gently to flatten the flatlock stitching. The stitch will spread out as the fabric opens.
  7. Finish by drawing the thread chain to the inside, weaving it under the stitches, and trimming the excess.

A blind-hem presser foot can make this easier because its guide helps keep the fold ledge in a consistent position. Expect some stitch detail to show: this is a “not quite invisible” blind hem, not the same as a hand-sewn blind hem.

Three-Thread Rolled Lettuce Hem

A rolled lettuce hem is decorative rather than traditional. It suits a lightweight jersey T-shirt with a playful, ruffled edge, and it works particularly well when the fabric naturally wants to wave.

  1. Cut the T-shirt to its intended finished length because this hem is sewn directly on the raw edge rather than on a turned-up allowance.
  2. Thread and configure the overlocker for its three-thread rolled-hem setting, following your machine’s threading and stitch-finger instructions.
  3. For a deliberately stretched lettuce edge, one sewing blog starts with width 5, length 2 on the rolled-hem setting, and differential feed 0.6. Test these settings on your jersey and confirm the precise controls in your machine manual, because overlockers differ.
  4. Serge around the raw edge while gently stretching the jersey in front of and behind the presser foot. The stretching, combined with the low differential feed, creates the ruffled edge.
  5. Return to the beginning of the hem, overlap the stitching briefly, then chain off.
  6. Pull the thread chain to the wrong side, weave it through the rolled stitches, and trim it neatly.

For a straight rolled hem, sew the edge without deliberately creating the ruffled effect.

Fix Common Jersey Hem Problems

Wavy or Stretched-Out Hem

A wavy hem usually means the jersey was stretched while feeding, or the differential feed allowed the layers to advance unevenly. Keep the shirt supported on the machine bed, avoid pulling it, and test a higher differential-feed setting if the fabric continues to ripple.

For a standard folded hem, press the overlocked edge before turning it up. The edge control from the overlocking often prevents the fold from rolling and reduces the temptation to tug it flat.

Curling Edge That Will Not Stay Folded

Some single jerseys curl strongly toward one side. Press the edge toward the wrong side and hold it with clips or basting while stitching.

For a different finish, choose a flatlock hem or make the edge part of the design with a rolled lettuce edge. Trying to force a very curling knit into a narrow folded hem can produce a bulky, uneven result.

Bunching or Tunneling Under the Stitching

Bunching happens when the stitching is too tight or too dense for the jersey. Test a different stretch stitch or adjust the stitch setup on a scrap that includes the same folded, overlocked layers.

A twin needle can create a familiar T-shirt look, so test it on the prepared scrap before sewing the shirt. Keep the hem flat and let the machine feed it evenly.

Popped Stitches When the Shirt Is Pulled On

Popped stitches mean the final seam is unsuitable for the jersey. Replace a straight stitch with a stretch-capable stitch, retest it across the direction of greatest stretch, and make sure the thread tension is not drawing the fabric into a rigid line.

Check the Finished T-Shirt Hem

Before putting the shirt away, run through this short check:

  • The hem is even all the way around.
  • The overlocked raw edge is enclosed inside a folded hem, or intentionally visible as part of a rolled or flatlock finish.
  • The right side is smooth, without ripples or puckers.
  • The hem stretches without thread snapping.
  • The starting and ending thread chains are woven in or otherwise secured.
  • The inside is comfortable against the skin, especially where the hem crosses side seams.

If the hem is wavy but the stitching itself is sound, pressing may improve it.

Frequently Asked Questions

Can You Sew a Hem With an Overlocker?

Yes, but the result depends on the stitch you choose. For a classic T-shirt hem, use the overlocker to finish the raw edge, turn the fabric up once, and stitch the fold with a stretch-capable sewing-machine stitch. For an overlocker-only finish, use a two-thread flatlock hem or a three-thread rolled hem.

How Do You Get a Small Hem on an Overlocker?

A rolled hem gives the smallest-looking overlocker finish because the machine wraps thread around the raw edge instead of enclosing a wide folded allowance. Use a rolled hem when you want a delicate edge or a decorative finish on lightweight jersey. Test the rolled finish on a scrap before sewing the shirt.

How Do You Sew a Blind Hem on an Overlocker?

Use a two-thread wide flatlock stitch and fold the pressed hem back to create a ledge for the stitch to catch. Stitch along that ledge, then open and pull the fabric gently so the flatlock spreads flat. One side will show a subtle stitch pattern, while the other has the flatlock ladder threads.

Why Does My Jersey Hem Wave After Overlocking?

The knit is not advancing evenly through the overlocker. Support the shirt’s weight, avoid pulling on either side of the presser foot, and test differential-feed adjustments on a scrap before sewing the garment. A wavy edge is desirable only for a lettuce hem, where the jersey is intentionally stretched as it is sewn.

Does a Jersey T-Shirt Hem Need to Be Double Folded?

No. A single turn over an overlocked edge is usually cleaner and less bulky for jersey. Hem depth should suit the garment shape and fabric weight, a general principle explained in New Mexico State University’s guide to making garment hems. Mark your preferred depth, test the finish on a scrap, then hem the shirt with the method that gives the smoothest stretch.

Do You Have to Overlock a Jersey Hem Before Stitching It?

No, you do not have to overlock a jersey hem before stitching it. Because knit fabric does not unravel like woven fabric, you can turn the hem up once before securing it. Overlocking first can make the folded edge easier to manage.