How to Make a Drape With Lining
To make a drape with lining, measure from the installed curtain hardware, cut the decorative fabric and lining, hem their bottom edges separately, and join them at the sides and top while leaving the lining’s bottom free. The method below makes a flat-top panel for clip rings, with enclosed edges and a lining that stays hidden behind the decorative fabric. Make one panel for a single drape or repeat the process for a matching pair.
What Lining Does for a Drape
A lined drape has two layers: the decorative fabric facing the room and a backing fabric facing the window. Lining adds body and helps protect the decorative fabric from sunlight, according to Sailrite.
The lining also gives the back of the curtain a finished appearance. Depending on the material, it can improve privacy or block light passing through the fabric.
Lining and interlining are different. Lining is the visible backing; interlining is an additional layer between the decorative fabric and lining. This tutorial uses ordinary lining, without interlining, to keep the construction manageable.
Materials and Tools for Lined Drapes
Choose your hardware and establish the finished measurements before buying fabric. The cutting calculations account for hems, but patterned fabric may need additional yardage to match motifs across panels.
Materials
- Decorative drapery fabric
- Drapery lining suited to your privacy and light-control needs
- Matching sewing thread
- A hand-sewing needle
- Curtain rod and clip rings suitable for the finished panel’s weight
- Optional basting tape and drapery weights
For temporary help holding folds, Sailrite’s panel-drape method lists SewReady Seamstick 3/8″ Basting Tape for Canvas (50 yds.). It is optional here: test its suitability on scraps before putting adhesive on your curtain fabric, and do not use it instead of permanent stitching.
For hems that need extra weight, Sailrite lists Drapery Weight No Tab 1″ #100186. A weight can be enclosed in a fabric pocket and secured inside a lower corner so it does not shift.
Tools
- Sewing machine
- Fabric scissors or rotary cutter and cutting mat
- Measuring tape
- Clear ruler
- Fabric-safe marking tool
- Iron, ironing board, and pressing cloth
- Pins or fabric clips
- Seam ripper
Sailrite’s listed pin option is Multiuse Pins 1-1/2″ (250 pack) #102985. For coated blackout lining, fabric clips can hold layers without making unnecessary holes.
How to Sew a Lined Drape
Use double-fold hems for the decorative fabric and lining, and finish the panel with a flat heading for clip rings. A double-fold hem means folding the fabric by the stated amount twice, enclosing the raw edge.
Step 1: Install the Hardware and Measure the Finished Panel
- Install the rod and fit the rings. For tieback-style drapes, establish the rod and tieback positions before sewing, following Sailrite’s hardware-first build order.
- Measure the width you want the curtains to cover. Use the working rod span, not simply the width of the window glass. Include any extra coverage needed at the sides or center.
- Calculate the flat panel width. For this gathered, clip-ring style, use twice the covered width as the combined finished fabric width. Divide that total by the number of panels.
- Measure the finished drop. Measure from where the panel’s top edge will sit in the clips to the desired bottom edge. Do not measure from the top of the rod unless that is actually where the fabric will begin.
Record these two measurements:
- W: finished flat width of one panel, before gathering
- L: finished length of one panel
If the curtains will reach the floor, measure at several points across the opening. An uneven floor can make otherwise matching panels appear different lengths.
Choose the lining before preparing and cutting the fabric:
| Your Main Goal | Suitable Lining | What to Consider |
|---|---|---|
| A finished backing with added body | Standard cotton or cotton-blend drapery lining | Choose care requirements compatible with the decorative fabric |
| Less light passing through the panel | Blackout drapery lining | Coated surfaces may need special handling when pressing and pinning |
| A softer, fuller-looking panel | Napped or combination lining | Added thickness increases bulk at hems and the heading |
Step 2: Prepare the Fabrics
- Read the care information for both fabrics. If both are washable and you intend to wash the finished drapes, preshrink them using compatible care methods. Do not automatically wash dry-clean-only fabric or coated lining.
- Press out storage creases. Use a pressing cloth where appropriate and a heat setting suitable for the more sensitive material. Do not iron a coated surface unless its manufacturer permits it.
- Identify the right and wrong sides. Mark the wrong sides unobtrusively so the lining will face the window correctly.
- Check the pattern direction and usable width. Exclude tight or distorted selvages from the working width.
For patterned fabric, decide which motif should appear at the top of each panel. Matching the cut lengths alone will not necessarily align the pattern.
Step 3: Calculate and Cut the Pieces
The allowances for this particular pattern are:
- Decorative fabric: double 1½-inch side hems, a double 4-inch bottom hem, and a double 2-inch top heading.
- Lining: use double-fold side and bottom hems. Its raw top edge will be enclosed in the heading.
| Piece for One Panel | Cut Width | Cut Length |
|---|---|---|
| Decorative fabric | W + 6 inches | L + 12 inches |
| Lining | W | L + hem allowance |
Allow additional fabric for shrinkage, squaring, and pattern matching.
- Square the first cut edge to the fabric grain.
- Mark and cut the decorative pieces.
- Cut the lining pieces separately.
- Label the top and panel position on the wrong side.
If a panel needs more than one fabric width, join the lengths before hemming. Match the pattern, account for the fabric consumed by the seams, finish the seam allowances, and press them flat. Then trim the assembled piece to the required cut dimensions.
Step 4: Hem the Bottom Edges and Lining Sides
- Hem the decorative fabric’s bottom. With the wrong side facing up, fold the bottom edge up 4 inches, press, then fold it up another 4 inches. Stitch close to the inner folded edge, or use a blind hem for a less visible finish.
- Hem the lining’s sides. Turn each side edge under ½ inch twice, press, and stitch near the inner fold.
- Hem the lining’s bottom. Fold the bottom edge up, press, then fold it over again to create a double hem. Stitch.
- Leave the lining’s top edge raw. It needs no separate hem because the decorative heading will enclose it.
Keep the fabric supported as you sew. Letting a long panel drag off the table can pull the layers and make an otherwise straight hem ripple.
Step 5: Press the Decorative Side Hems and Heading
- Lay the decorative fabric right side down.
- Fold each side edge inward 1½ inches twice and press. Leave these folds unstitched.
- Fold the top edge down 2 inches twice and press. Leave the heading unstitched as well.
- Check the panel’s width and length between its finished-edge creases.
These pressed folds establish the panel’s final outline. Correct any unevenness now, before attaching the lining.
If you are using weights, secure each one inside a closed fabric pocket in the decorative bottom hem. Keep it clear of the needle path and make the attachment accessible if the weight must be removed for cleaning.
Step 6: Position and Attach the Lining
The decorative fabric and lining are joined at the sides and top, while the lining’s bottom edge remains free.
- Open the decorative side folds and top heading enough to insert the lining.
- Lay the lining on the decorative fabric with wrong sides together. The lining’s finished, window-facing side should face you.
- Center the lining between the panel’s finished side creases.
- Align the lining’s raw top edge with the crease that will become the panel’s finished top edge, not with the decorative fabric’s raw cut edge.
- Smooth the lining without stretching it. Its bottom should finish above the decorative hem.
- Refold the decorative side hems over the lining’s finished side edges. Pin or clip them in place.
Hand-slipstitch the inner folded edge of each decorative side hem to the lining. Catch the lining and the folded hem, rather than sewing through the curtain’s front.
Below the lining, secure the remaining side-hem ends to the decorative bottom hem. Do not stitch across the lining’s bottom edge or attach that edge to the face fabric.
If the lining pulls taut before the sides lie flat, reposition it rather than stretching it into place.
Step 7: Close the Heading
- Refold the decorative top heading.
- Check that the lining’s raw top edge is enclosed in the heading and its side edges remain tucked beneath the decorative side hems.
- Pin or baste the heading flat.
- Machine-stitch close to its lower folded edge, catching the lining underneath.
- Secure the stitching ends and remove temporary basting.
The heading supports the panel, so use permanent stitching even if basting tape helped hold the fold.
Keep the top corners square and make sure the side hems remain tucked inside the heading.
Step 8: Hang and Finish the Panel
- Give the panel a final press appropriate to both fabrics.
- Attach the clip rings evenly across the reinforced heading, gripping the complete heading rather than the lining alone.
- Hang the panel and arrange the folds.
- Open and close the curtain to check that the rings move freely.
- Inspect the hem and lining from the room side and the window side.
For a pair, hang both panels before making any final adjustments. If the top edges are level but the bottoms differ, check the hem folds and floor level before shortening either curtain.
Adapting Lined Drapes for Other Projects
Existing curtains can be lined through the heading. For pinch-pleated drapes, the tape-based method uses pleating tape, compatible hooks, and fullness suited to the covered width.
Add Lining to Existing Curtains
You can line an existing curtain without taking the whole panel apart. This approach works best when the lower edge of its heading can be opened and restitched without damaging a pocket, tape, or other hanging mechanism.
- Remove and prepare the curtain. Take it down, remove detachable hardware, and press it. Prepare the lining for the cleaning method the finished curtain will need.
- Measure the lining area. Plan a finished lining width 2 inches narrower than the curtain. Measure its height from the intended raw-edge position inside the heading to above the curtain’s bottom.
- Add hem allowances for the lining’s side and bottom hems, and subtract a bottom clearance so the finished lining ends above the decorative hem.
- Cut and hem the lining. Make double-fold side and bottom hems. Leave the top raw.
- Open the heading’s lower stitching. Slide the lining’s raw top into the heading, center it, and resew the opened seam. Preserve any rod channel, hook pockets, or drawcords.
- Attach the sides loosely. Slipstitch the lining’s side edges to the backs of the curtain’s side hems without stitching through the visible front. Leave the bottom free.
- Press and rehang. Replace the hardware, check that the lining is hidden, and test the curtain’s movement.
If opening the heading would damage it, use a separate lining attachment designed for that heading instead of cutting into grommets or structural stitching.
Make Lined Pinch-Pleated Drapes
Pinch pleats need a different heading plan from clip-ring panels. Choose the pleating tape and compatible hooks before calculating the cut dimensions.
- Plan the fullness. Pinch-pleated drapes commonly use about 2 to 2½ times the covered width. Use the fullness specified for your chosen tape when calculating the actual panel.
- Change the top allowance. Keep the decorative side and bottom allowances, but replace the flat-top heading allowance with the amount required to finish the top and accommodate the tape. The lining’s raw top must still be enclosed behind the finished top edge.
- Construct the lined panel. Hem the decorative bottom and lining separately, attach the lining at the sides, and finish the top with enough depth for the tape.
- Sew on the tape. Position it on the back of the heading and stitch along its designated sewing lines. Do not close hook pockets or stitch across working drawcords.
- Form the pleats. Use the tape’s intended hooks or drawcord arrangement, distributing the pleats to achieve the required coverage. Secure drawcord ends without cutting them off.
- Hang and adjust. Insert the remaining hooks, hang the drape, and adjust the hook positions so the heading and hem sit evenly. Check that the curtains close without straining the pleats.
Do not simply pleat a panel already sized for a flat, ungathered appearance: the pleats consume width.
Check the Finished Drape
Inspect the curtain while it is hanging, not just while it lies on the table.
- The lining stays hidden. It should not show along the sides or below the decorative hem.
- The side edges hang straight. A curled edge can signal an attachment problem.
- The bottom hangs freely. Look for a lifted hem or diagonal wrinkles.
- The heading remains level. Clips or hooks should support the panel consistently.
- The curtain operates smoothly. The hardware should move without binding under the added fabric weight.
If one area pulls, release the nearby attachment stitches and let the layers settle before restitching. If the lining peeks out, check its placement and hem before trimming it.
Once the hang is right, trim loose threads, remove remaining pins, and keep the care information for both fabrics together.
Frequently Asked Questions
Do Curtains Need a Liner?
No. Sheers and some lightweight decorative curtains are intentionally unlined. Add lining when you want a finished backing, more body, better privacy, or less light passing through the panel.
Will Blackout Lining Make the Room Completely Dark?
Blackout lining blocks light through the fabric, but light can still enter around the sides, above the rod, and between panels. For stronger room-darkening performance, plan sufficient overlap and coverage around the window as well as choosing blackout material.
Can I Wash Lined Drapes?
Only if the decorative fabric, lining, thread, and attached components are compatible with washing. Different shrinkage rates can make the finished panel pucker or cause the lining to show below the hem. Choose compatible materials before sewing and use the cleaning method permitted by the most restrictive component.
Can I Make Lined Drapes for an Institution?
Yes, but confirm the institution’s requirements before purchasing materials. Schools, care facilities, theaters, and other public settings may require documented flame-performance testing, approved hardware, or particular cleaning procedures. A home-sewn curtain is not automatically suitable, and a flame-resistant lining does not establish that the entire finished drape meets the required specification.
